| About Us | Products | Contact Us |..................


LPG Tank Equipment and LPG Valves






Internal Pressure Relief Valves for Asme And Dot Containers
Designed specifically for use as a primary pressure relief device on ASME containers up to 2000 gallon water capacity.
Furnished with rain cap for protection against contamination. See ordering information for part numbers.
All these valves have a pre-applied sealant on the container connection.
All these valves are ASME approved.

DK FLAME LGP VALVES2 DK FLAME LGP VALVES2
Ordering Information

Part
Number
Container
Connection
Start to Discharge
Setting PSIC
UL (at 120% of set pressure)
Flow capacity SCFM/AIR

ASME (at 120% of set pressure)
Flow capacity SCFM/AIR
Wrench
Hex Flat
66.1127
1" NPT

375
1491

n/a
1-5/16"
66.1128
3/4" NPT
250
2007
1807
1-9/16"
66.1129
1" NPT
250
2757
2493
1-3/4"
66.1130
1-1/4" NPT
250
4312
3913
2-1/4"
66.1242 (fully internal)
1" NPT
312
1109
979
1-5/16"
66.1135 (fully internal)
1" NPT
250
864
786
1-5/16"
66.1162 3/4"-NPT 312 690 690 11/16"

 

 

External Pressure Relief Valves
DK FLAME LGP VALVES3 DK FLAME LGP VALVES3 DK FLAME LGP VALVES3
Ordering Information

Part
Number
Bottom Male Connection Wrench grip hexagon (mm) Thread type Configuration suitable for this tank capacity:

PRV - Start to Discharge Setting (PSIC) PRV-OVERPRESSURE 10%
CAPACITY NmVmin.
(If not specified otherwise)
Approval PRV
Orifice
(mm)
taper
parallel
66.1139 - PRV
1/4-18 NPT

22 x   - 250 18,41
(at 120%0-P.SCFM-AIR)
UL/ASME
19,00
66.1140 - PRV
1/4-18 NPT
22 x   - 375 33,52 (at 120%0,P.SCFM-AIR) UL
19,00
70.0073 - EU19 3/4"-NPT - x   - 250 1808
(at 20%0-P.SCFM-AIR)
UL/ASME  


LPC Float Gauges Flanged four Bolt Model
These float gauges flanged four bolt models include a mounting.
DK FLAME LGP VALVES6

Part
Number
Nominal 0 Inches Diameter 0 mm Tank Type
Container Gallons
Capacity Liters Dimension (mm)

          A B
2069.U 24"
609,60
horizontal
120

454,25

338
285
2070.U
30"
762,00
horizontal
250/320
946,35/1.211,328
412
360
2071.U
37"
939,80
horizontal
500
1.892,70
510
438
2072.U
41"
1.041,40
horizontal
1.000 3.785,40 553
477
2073.U
48"
1.219,20
horizontal
- - 612
535
2075.U 30" 762,00 vertical - - 640 430


LPC Threaded Float Gauges

All level gauges are produced in compliance with the CEN TC 286-prEN 13799 standard. The float is made in SPANSIL rubber.
This kind of material, cannot be detached from its lodging when in touch with caustic soda. These level gauges have been manufactu¬red in accordance with the best available technology: a tropicalised zamac has been used both for the head and the gearing. DK FLAME LGP VALVES6 ..................................................